![]() Rear Facing (with routing for smaller children) – 1 and shortened by routing back through slot 2 The crotch buckle should be close to your child, but not under their bottom. Reattach the hook and loop closure on the harness covers, over the harness straps. Fold the harness covers down towards the harness straps and place the harness straps inside the harness covers. Slide the harness covers behind the headrest pad with the back of the covers facing you. To reinstall the harness covers, undo the snaps on the headrest pad. Then, slide the harness covers out from behind the head pad. To remove the covers, undo the snaps on the hardest pad and undo the hook and loop closure on the harness pads. If you can not get the chest clip in the proper position when using the harness covers, remove them until the child is larger. The harness covers can be used both in rear and forward facing mode and are optional at all times. They also MUST be used when using the harness routing for smaller children.īuckle CoverThe buckle cover is optional at all times and can be used in rear and forward facing modes. The head and body pillows are for use in the rear facing mode only and MUST be used together. Safety 1st Grow and Go Extend ‘n Ride LX head and body pillows While the cupholders are in the dishwasher (or otherwise not attached to the seat), the seat cannot be used so make sure to plan your trips around clean cupholders! Snack Tray To remove them, twist the cup holder counterclockwise and lift it straight up out of the shell of the car seat. The cupholders are required for use, they are removable and can be washed in the dishwasher on the top rack only. When the child is large enough to fit in the regular harness setting, reverse this process to re-thread the harness and move it back into the other slot. Note: when using this harness routing, the head and body inserts MUST be used. Attach the 2nd set of harness loops to the splitter plate. Then, thread the harness into the lowest slots in the body insert, seat pad, and shell of the car seat. Place the head and body insert into the seat, ensuring the crotch buckle is in the same slot in the shell, seat pad, and body insert. Pull the harness out from the front of the car seat. To use this routing, lower the headrest to the lowest setting, loosen the harness all of the way, then flip the seat over and remove the harness from the splitter plate. The harness must be manually re-routed to use this setting. If the harness cannot be adjusted to be small enough for a tiny passenger, there are harness loops that create a smaller setting. Newborn harness routing for smaller children The harness easily adjusts by raising and lowering the headrest.No-rethread harness when not using the newborn setting.It adds extra legroom when the seat is in rear facing mode. Foot panel that can be used in forward facing mode as a footrest.Width at widest point (at child’s shoulders and cupholders): 18.5 inches. ![]() Highest booster guide position: 18 inches.Lowest no rethread harness position: 10 inches.The harness must be threaded separately into this slot when it’s being used. Lowest harness position: 5.75 inches with insert.Standard, j-hook lower anchor connectors.Top tether anchor: required for forward facing mode.High back booster height range: 43-52 inches tall.High back booster weight range: 40-100 pounds.Forward facing height range: 29-49 inches tall.Forward facing weight range: 22-65 pounds.Rear facing height range: 19-40 inches tall.Now that we know what makes this seat unique, let’s take a closer look. That same panel becomes a footrest for forward facing children, which is something we often see caregivers ask for to keep their child’s legs from dangling in a forward facing car seat. Safety 1st has listened to caregivers who are looking for extra leg room for their kiddos and created the Grow and Go Extend ‘n Ride LX, which includes a leg extension panel. The Grow and Go family of multimode car seats has grown again. Safety 1st Grow and Go Extend ‘n Ride LX installed rear racing with seat belt
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |